FS#61029 - Linux 4.19.8 Still Breaks My Networking

Attached to Project: Arch Linux
Opened by Alberto Díaz López (Takuya) - Tuesday, 11 December 2018, 10:22 GMT
Last edited by Doug Newgard (Scimmia) - Tuesday, 11 December 2018, 14:16 GMT
Task Type Bug Report
Category Packages: Core
Status Closed
Assigned To No-one
Architecture x86_64
Severity Critical
Priority Normal
Reported Version
Due in Version Undecided
Due Date Undecided
Percent Complete 100%
Votes 0
Private No

Details

Description: Again, Linux 4.19.8, which it supposed to solve the issue with the networking drivers (r8169), applied on Linux 4.19.7, still fails sometimes.


Additional info:
* package version(s)
Linux 4.19.8
* config and/or log files etc.

Example when the networking starts working (Linux 4.19.8):
[ 2.047371] r8169 0000:03:00.0 enp3s0: renamed from eth0
[ 2.562520] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 2.691421] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 5.608366] r8169 0000:03:00.0 enp3s0: Link is Up - 1Gbps/Full - flow control off
[ 5.608378] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready

Example when the networking starts working but i suspend and restore the system and the networking be becomes disabled (Linux 4.19.8):
[ 2.055452] r8169 0000:03:00.0 enp3s0: renamed from eth0
[ 2.607507] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 2.734886] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 5.597521] r8169 0000:03:00.0 enp3s0: Link is Up - 1Gbps/Full - flow control off
[ 5.597528] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 147.680889] r8169 0000:03:00.0 enp3s0: Link is Down
[ 147.902398] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 148.040553] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready

Example when the networking starts disabled (Linux 4.19.8):
[ 2.003255] r8169 0000:03:00.0 enp3s0: renamed from eth0
[ 2.614280] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 2.741405] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 5.676023] r8169 0000:03:00.0 enp3s0: Link is Up - 1Gbps/Full - flow control off
[ 5.676036] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 6.382786] r8169 0000:03:00.0 enp3s0: Link is Down

Steps to reproduce:
- Start the system normally.
- Wait and see when everything is loaded, to the network manager icon at the systray, if there's an advice or not, or look at the router, to the pertinent light and see if after the initial Linux load, if the light is turned off or turned on, that is valid too
This task depends upon

Closed by  Doug Newgard (Scimmia)
Tuesday, 11 December 2018, 14:16 GMT
Reason for closing:  Duplicate
Additional comments about closing:   FS#60832 

Loading...