This is a pre-release version of the X server from The X.Org Foundation. It is not supported in any way. Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/. Select the "xorg" product for bugs you find in this release. Before reporting bugs in pre-release versions please check the latest version in the X.Org Foundation git repository. See http://wiki.x.org/wiki/GitPage for git access instructions. X.Org X Server 1.7.1.901 (1.7.2 RC 1) Release Date: 2009-11-6 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.31-ARCH x86_64 Current Operating System: Linux laptop 2.6.31-ARCH #1 SMP PREEMPT Tue Nov 10 19:01:40 CET 2009 x86_64 Kernel command line: root=/dev/disk/by-uuid/b4d6a332-1631-42ff-be7f-2a74e910da24 ro i915.modeset=1 Build Date: 08 November 2009 04:08:18PM Current version of pixman: 0.16.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Nov 17 08:20:38 2009 (II) Loader magic: 0x7c1a00 (II) Module ABI versions: X.Org ANSI C Emulation: 0.4 X.Org Video Driver: 6.0 X.Org XInput driver : 7.0 X.Org Server Extension : 2.0 (--) using VT number 7 (--) PCI:*(0:0:2:0) 8086:2a02:1019:9933 Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller rev 3, Mem @ 0xfc000000/1048576, 0xd0000000/268435456, I/O @ 0x00001800/8 (--) PCI: (0:0:2:1) 8086:2a03:1019:9933 Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller rev 3, Mem @ 0xfc100000/1048576 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default intel Device 0" Driver "intel" EndSection Section "Screen" Identifier "Builtin Default intel Screen 0" Device "Builtin Default intel Device 0" EndSection Section "Device" Identifier "Builtin Default vesa Device 0" Driver "vesa" EndSection Section "Screen" Identifier "Builtin Default vesa Screen 0" Device "Builtin Default vesa Device 0" EndSection Section "Device" Identifier "Builtin Default fbdev Device 0" Driver "fbdev" EndSection Section "Screen" Identifier "Builtin Default fbdev Screen 0" Device "Builtin Default fbdev Device 0" EndSection Section "ServerLayout" Identifier "Builtin Default Layout" Screen "Builtin Default intel Screen 0" Screen "Builtin Default vesa Screen 0" Screen "Builtin Default fbdev Screen 0" EndSection (==) --- End of built-in configuration --- (==) ServerLayout "Builtin Default Layout" (**) |-->Screen "Builtin Default intel Screen 0" (0) (**) | |-->Monitor "" (**) | |-->Device "Builtin Default intel Device 0" (==) No monitor specified for screen "Builtin Default intel Screen 0". Using a default monitor configuration. (**) |-->Screen "Builtin Default vesa Screen 0" (1) (**) | |-->Monitor "" (**) | |-->Device "Builtin Default vesa Device 0" (==) No monitor specified for screen "Builtin Default vesa Screen 0". Using a default monitor configuration. (**) |-->Screen "Builtin Default fbdev Screen 0" (2) (**) | |-->Monitor "" (**) | |-->Device "Builtin Default fbdev Device 0" (==) No monitor specified for screen "Builtin Default fbdev Screen 0". Using a default monitor configuration. (==) Automatically adding devices (==) Automatically enabling devices (==) FontPath set to: /usr/share/fonts/misc, /usr/share/fonts/100dpi:unscaled, /usr/share/fonts/75dpi:unscaled, /usr/share/fonts/TTF, /usr/share/fonts/Type1 (==) ModulePath set to "/usr/lib/xorg/modules" (II) Cannot locate a core pointer device. (II) Cannot locate a core keyboard device. (II) The server relies on HAL to provide the list of input devices. If no devices become available, reconfigure HAL or disable AllowEmptyInput. (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory) (II) LoadModule: "extmod" (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "dbe" (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "glx" (II) Loading /usr/lib/xorg/modules/extensions/libglx.so (II) Module glx: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.0.0 ABI class: X.Org Server Extension, version 2.0 (==) AIGLX enabled (II) Loading extension GLX (II) LoadModule: "record" (II) Loading /usr/lib/xorg/modules/extensions/librecord.so (II) Module record: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 2.0 (II) Loading extension RECORD (II) LoadModule: "dri" (II) Loading /usr/lib/xorg/modules/extensions/libdri.so (II) Module dri: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.0.0 ABI class: X.Org Server Extension, version 2.0 (II) Loading extension XFree86-DRI (II) LoadModule: "dri2" (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so (II) Module dri2: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.1.0 ABI class: X.Org Server Extension, version 2.0 (II) Loading extension DRI2 (II) LoadModule: "intel" (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so (II) Module intel: vendor="X.Org Foundation" compiled for 1.7.1, module version = 2.9.1 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 6.0 (II) LoadModule: "vesa" (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so (II) Module vesa: vendor="X.Org Foundation" compiled for 1.7.0.901, module version = 2.2.1 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 6.0 (II) LoadModule: "fbdev" (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so (II) Module fbdev: vendor="X.Org Foundation" compiled for 1.7.0.901, module version = 0.4.1 ABI class: X.Org Video Driver, version 6.0 (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale (II) VESA: driver for VESA chipsets: vesa (II) FBDEV: driver for framebuffer: fbdev (II) Primary Device is: PCI 00@00:02:0 (WW) Falling back to old probe method for vesa (WW) Falling back to old probe method for fbdev (II) Loading sub module "fbdevhw" (II) LoadModule: "fbdevhw" (II) Loading /usr/lib/xorg/modules/linux/libfbdevhw.so (II) Module fbdevhw: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 0.0.2 ABI class: X.Org Video Driver, version 6.0 (EE) open /dev/fb0: No such file or directory (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/lib/xorg/modules/libvgahw.so (II) Module vgahw: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 0.1.0 ABI class: X.Org Video Driver, version 6.0 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Module "ramdac" already built-in drmOpenDevice: node name is /dev/dri/card0 drmOpenByBusid: Searching for BusID pci:0000:00:02.0 drmOpenDevice: node name is /dev/dri/card0 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card1 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card2 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card3 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card4 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card5 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card6 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card7 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card8 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card9 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card10 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card11 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card12 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card13 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card14 drmOpenByBusid: drmOpenMinor returns -1 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: node name is /dev/dri/card1 drmOpenDevice: node name is /dev/dri/card2 drmOpenDevice: node name is /dev/dri/card3 drmOpenDevice: node name is /dev/dri/card4 drmOpenDevice: node name is /dev/dri/card5 drmOpenDevice: node name is /dev/dri/card6 drmOpenDevice: node name is /dev/dri/card7 drmOpenDevice: node name is /dev/dri/card8 drmOpenDevice: node name is /dev/dri/card9 drmOpenDevice: node name is /dev/dri/card10 drmOpenDevice: node name is /dev/dri/card11 drmOpenDevice: node name is /dev/dri/card12 drmOpenDevice: node name is /dev/dri/card13 drmOpenDevice: node name is /dev/dri/card14 (EE) intel(0): [drm] Failed to open DRM device for : No such file or directory (EE) intel(0): Failed to become DRM master. (II) intel(0): Creating default Display subsection in Screen section "Builtin Default intel Screen 0" for depth/fbbpp 24/32 (==) intel(0): Depth 24, (--) framebuffer bpp 32 (==) intel(0): RGB weight 888 (==) intel(0): Default visual is TrueColor (II) intel(0): Integrated Graphics Chipset: Intel(R) 965GM (--) intel(0): Chipset: "965GM" (--) intel(0): Linear framebuffer at 0xD0000000 (--) intel(0): IO registers at addr 0xFC000000 size 1048576 (WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB (II) intel(0): No SDVO device is found in VBT (II) intel(0): 2 display pipes available. (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Module "ddc" already built-in (II) Loading sub module "i2c" (II) LoadModule: "i2c" (II) Module "i2c" already built-in (II) intel(0): Output VGA has no monitor section (II) intel(0): Output LVDS has no monitor section (II) intel(0): I2C bus "LVDSDDC_C" initialized. (II) intel(0): Attempting to determine panel fixed mode. (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0. (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): Output VGA disconnected (II) intel(0): Output LVDS connected (II) intel(0): Using exact sizes for initial modes (II) intel(0): Output LVDS using initial mode 1280x800 (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. (II) intel(0): detected 512 kB GTT. (II) intel(0): detected 7676 kB stolen memory. (==) intel(0): video overlay key set to 0x101fe (==) intel(0): DPI set to (96, 96) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/lib/xorg/modules/libfb.so (II) Module fb: vendor="X.Org Foundation" compiled for 1.7.1.901, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.4 (II) intel(0): Comparing regs from server start up to After PreInit (WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd0000009 (WW) intel(0): PP_STATUS before: on, ready, sequencing idle (WW) intel(0): PP_STATUS after: on, ready, sequencing on (WW) intel(0): Register 0x71024 (PIPEBSTAT) changed from 0x00000206 to 0x80000206 (WW) intel(0): PIPEBSTAT before: status: VSYNC_INT_STATUS SVBLANK_INT_STATUS VBLANK_INT_STATUS (WW) intel(0): PIPEBSTAT after: status: FIFO_UNDERRUN VSYNC_INT_STATUS SVBLANK_INT_STATUS VBLANK_INT_STATUS (II) UnloadModule: "vesa" (II) Unloading /usr/lib/xorg/modules/drivers/vesa_drv.so (II) UnloadModule: "fbdev" (II) Unloading /usr/lib/xorg/modules/drivers/fbdev_drv.so (II) UnloadModule: "fbdevhw" (II) Unloading /usr/lib/xorg/modules/linux/libfbdevhw.so (==) Depth 24 pixmap format is 32 bpp (II) intel(0): Kernel reported 488960 total, 1 used (II) intel(0): I830CheckAvailableMemory: 1955836 kB available (WW) intel(0): DRI2: failed to open drm device (**) intel(0): Framebuffer compression disabled (**) intel(0): Tiling enabled (**) intel(0): SwapBuffers wait enabled (EE) intel(0): Failed to initialize kernel memory manager (==) intel(0): VideoRam: 262144 KB (II) intel(0): Attempting memory allocation with tiled buffers. (II) intel(0): Tiled allocation successful. (II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) UXA(0): Driver registered support for the following operations: (II) solid (II) copy (II) composite (RENDER acceleration) (==) intel(0): Backing store disabled (==) intel(0): Silken mouse enabled (II) intel(0): Initializing HW Cursor (WW) intel(0): drmSetMaster failed: Bad file descriptor (II) intel(0): xf86BindGARTMemory: bind key 0 at 0x0077f000 (pgoffset 1919) (II) intel(0): xf86BindGARTMemory: bind key 1 at 0x0082a000 (pgoffset 2090) (II) intel(0): xf86BindGARTMemory: bind key 2 at 0x0082b000 (pgoffset 2091) (II) intel(0): xf86BindGARTMemory: bind key 3 at 0x00c13000 (pgoffset 3091) (II) intel(0): Fixed memory allocation layout: (II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB) (II) intel(0): 0x00020000-0x00029fff: HW cursors (40 kB) (II) intel(0): 0x0002a000-0x00829fff: fake bufmgr (8192 kB) (II) intel(0): 0x0077f000: end of stolen memory (II) intel(0): 0x0082a000-0x0082afff: overlay registers (4 kB) (II) intel(0): 0x0082b000-0x00c12fff: front buffer (4000 kB) X tiled (II) intel(0): 0x00c13000-0x00c13fff: power context (4 kB) (II) intel(0): 0x10000000: end of aperture (II) intel(0): BO memory allocation layout: (II) intel(0): using SSC reference clock of 96 MHz (II) intel(0): Selecting standard 18 bit TMDS pixel format. (II) intel(0): Output configuration: (II) intel(0): Pipe A is off (II) intel(0): Display plane A is now disabled and connected to pipe A. (II) intel(0): Pipe B is on (II) intel(0): Display plane B is now enabled and connected to pipe B. (II) intel(0): Output VGA is connected to pipe none (II) intel(0): Output LVDS is connected to pipe B (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. (==) intel(0): DPMS enabled (==) intel(0): Intel XvMC decoder disabled (II) intel(0): Set up textured video (II) intel(0): Set up overlay video (II) intel(0): direct rendering: Failed (--) RandR disabled (II) Initializing built-in extension Generic Event Extension (II) Initializing built-in extension SHAPE (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension BIG-REQUESTS (II) Initializing built-in extension SYNC (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension XC-MISC (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE record: RECORD extension enabled at configure time. record: This extension is known to be broken, disabling extension now.. record: http://bugs.freedesktop.org/show_bug.cgi?id=20500 (II) AIGLX: Screen 0 is not DRI2 capable (II) AIGLX: Screen 0 is not DRI capable (II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 (II) intel(0): Setting screen physical size to 338 x 211 (II) config/hal: Adding input device Macintosh mouse button emulation (II) LoadModule: "evdev" (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so (II) Module evdev: vendor="X.Org Foundation" compiled for 1.7.0.901, module version = 2.3.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 7.0 (**) Macintosh mouse button emulation: always reports core events (**) Macintosh mouse button emulation: Device: "/dev/input/event0" (II) Macintosh mouse button emulation: Found 3 mouse buttons (II) Macintosh mouse button emulation: Found relative axes (II) Macintosh mouse button emulation: Found x and y relative axes (II) Macintosh mouse button emulation: Configuring as mouse (**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5 (**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200 (II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE) (**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1 (**) Macintosh mouse button emulation: (accel) acceleration profile 0 (II) Macintosh mouse button emulation: initialized for relative axes. (II) config/hal: Adding input device SynPS/2 Synaptics TouchPad (II) LoadModule: "synaptics" (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so (II) Module synaptics: vendor="X.Org Foundation" compiled for 1.7.0.901, module version = 1.2.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 7.0 (II) Synaptics touchpad driver version 1.2.0 (**) Option "Device" "/dev/input/event7" (II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472 (II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448 (II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255 (II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0 (II) SynPS/2 Synaptics TouchPad: buttons: left right middle double triple (**) Option "TapButton1" "1" (**) Option "TapButton2" "2" (**) Option "TapButton3" "3" (--) SynPS/2 Synaptics TouchPad: touchpad found (**) SynPS/2 Synaptics TouchPad: always reports core events (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD) (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1 (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 0 (--) SynPS/2 Synaptics TouchPad: touchpad found (II) config/hal: Adding input device AT Translated Set 2 keyboard (**) AT Translated Set 2 keyboard: always reports core events (**) AT Translated Set 2 keyboard: Device: "/dev/input/event1" (II) AT Translated Set 2 keyboard: Found keys (II) AT Translated Set 2 keyboard: Configuring as keyboard (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (II) config/hal: Adding input device Sleep Button (**) Sleep Button: always reports core events (**) Sleep Button: Device: "/dev/input/event5" (II) Sleep Button: Found keys (II) Sleep Button: Configuring as keyboard (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (II) config/hal: Adding input device Power Button (**) Power Button: always reports core events (**) Power Button: Device: "/dev/input/event3" (II) Power Button: Found keys (II) Power Button: Configuring as keyboard (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (II) config/hal: Adding input device Power Button (**) Power Button: always reports core events (**) Power Button: Device: "/dev/input/event2" (II) Power Button: Found keys (II) Power Button: Configuring as keyboard (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD) (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): Printing DDC gathered Modelines: (II) intel(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.3 kHz) (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): Printing DDC gathered Modelines: (II) intel(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.3 kHz) (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): EDID vendor "LPL", prod id 59392 (II) intel(0): Printing DDC gathered Modelines: (II) intel(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 -hsync -vsync (49.3 kHz) (II) intel(0): EDID vendor "LPL", prod id 59392