Linux version 2.6.27-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Sat Nov 8 10:11:43 UTC 2008 PAT WC disabled due to known CPU erratum. BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001f7d0000 (usable) BIOS-e820: 000000001f7d0000 - 000000001f7f0c00 (reserved) BIOS-e820: 000000001f7f0c00 - 000000001f7fc000 (ACPI NVS) BIOS-e820: 000000001f7fc000 - 000000001f800000 (reserved) last_pfn = 0x1f7d0 max_arch_pfn = 0x100000 kernel direct mapping tables up to 1f7d0000 @ 7000-d000 RAMDISK: 1f70e000 - 1f7bf5bd DMI 2.3 present. ACPI: RSDP 000F6C00, 0014 (r0 COMPAQ) ACPI: RSDT 1F7F0C84, 0030 (r1 COMPAQ CPQ0058 30080620 CPQ 1) ACPI: FACP 1F7F0C00, 0084 (r2 COMPAQ CPQ0058 2 CPQ 1) ACPI: DSDT 1F7F0D10, 623A (r1 HP nx5000 10000 MSFT 100000E) ACPI: FACS 1F7FBE80, 0040 ACPI: APIC 1F7F0CB4, 005A (r1 COMPAQ CPQ0058 1 CPQ 1) ACPI: SSDT 1F7F6F4A, 028A (r1 COMPAQ CPQGysr 1001 MSFT 100000E) ACPI: DMI detected: Hewlett-Packard 0MB HIGHMEM available. 503MB LOWMEM available. mapped low ram: 0 - 1f7d0000 low ram: 00000000 - 1f7d0000 bootmap 00002000 - 00005efc (9 early reservations) ==> bootmem [0000000000 - 001f7d0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 000050c280] TEXT DATA BSS ==> [0000100000 - 000050c280] #4 [001f70e000 - 001f7bf5bd] RAMDISK ==> [001f70e000 - 001f7bf5bd] #5 [000050d000 - 0000510000] INIT_PG_TABLE ==> [000050d000 - 0000510000] #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000] #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000] Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x0001f7d0 HighMem 0x0001f7d0 -> 0x0001f7d0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x0001f7d0 On node 0 totalpages: 128879 free_area_init_node: node 0, pgdat c03d8200, node_mem_map c1000000 DMA zone: 3967 pages, LIFO batch:0 Normal zone: 123904 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfec01000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information SMP: Allowing 1 CPUs, 0 hotplug CPUs mapped APIC to ffffb000 (fec01000) mapped IOAPIC to ffffa000 (fec00000) PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 Allocating PCI resources starting at 20000000 (gap: 1f800000:e0800000) PERCPU: Allocating 39324 bytes of per cpu data NR_CPUS: 16, nr_cpu_ids: 1, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127871 Kernel command line: root=/dev/disk/by-uuid/f0eeb230-32a2-4c97-aeeb-ae5943fe8b43 ro Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) TSC: PIT calibration confirmed by PMTIMER. TSC: using PMTIMER calibration value Detected 1495.139 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 506004k/515904k available (2147k kernel code, 9384k reserved, 844k data, 288k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffee8000 - 0xfffff000 (1116 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe0000000 - 0xff7fe000 ( 503 MB) lowmem : 0xc0000000 - 0xdf7d0000 ( 503 MB) .init : 0xc03f3000 - 0xc043b000 ( 288 kB) .data : 0xc0318f76 - 0xc03ec320 ( 844 kB) .text : 0xc0100000 - 0xc0318f76 (2147 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 2991.87 BogoMIPS (lpj=4983796) Security Framework initialized Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 9k freed ACPI: Core revision 20080609 ACPI: Checking initramfs for custom DSDT ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05 Brought up 1 CPUs Total of 1 processors activated (2991.87 BogoMIPS). net_namespace: 832 bytes Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3 PCI: Using configuration type 1 for base access ACPI: EC: Look up EC in DSDT ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in interrupt mode ACPI: PCI Root Bridge [C045] (0000:00) PCI: 0000:00:02.0 reg 10 32bit mmio: [98000000, 9fffffff] PCI: 0000:00:02.0 reg 14 32bit mmio: [90400000, 9047ffff] PCI: 0000:00:02.0 reg 18 io port: [2c30, 2c37] pci 0000:00:02.0: supports D1 PCI: 0000:00:02.1 reg 10 32bit mmio: [a0000000, a7ffffff] PCI: 0000:00:02.1 reg 14 32bit mmio: [90480000, 904fffff] pci 0000:00:02.1: supports D1 PCI: 0000:00:1d.0 reg 20 io port: [28c0, 28df] PCI: 0000:00:1d.1 reg 20 io port: [28e0, 28ff] PCI: 0000:00:1d.2 reg 20 io port: [2c00, 2c1f] PCI: 0000:00:1d.7 reg 10 32bit mmio: [90500000, 905003ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH4 GPIO PCI: 0000:00:1f.1 reg 10 io port: [0, 7] PCI: 0000:00:1f.1 reg 14 io port: [0, 3] PCI: 0000:00:1f.1 reg 18 io port: [0, 7] PCI: 0000:00:1f.1 reg 1c io port: [0, 3] PCI: 0000:00:1f.1 reg 20 io port: [2c20, 2c2f] PCI: 0000:00:1f.1 reg 24 32bit mmio: [0, 3ff] PCI: 0000:00:1f.5 reg 10 io port: [2000, 20ff] PCI: 0000:00:1f.5 reg 14 io port: [2880, 28bf] PCI: 0000:00:1f.5 reg 18 32bit mmio: [90600000, 906001ff] PCI: 0000:00:1f.5 reg 1c 32bit mmio: [90680000, 906800ff] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold pci 0000:00:1f.5: PME# disabled PCI: 0000:00:1f.6 reg 10 io port: [2400, 24ff] PCI: 0000:00:1f.6 reg 14 io port: [2800, 287f] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold pci 0000:00:1f.6: PME# disabled PCI: 0000:01:04.0 reg 10 32bit mmio: [90100000, 90100fff] PCI: 0000:01:06.0 reg 10 32bit mmio: [90180000, 90180fff] pci 0000:01:06.0: supports D1 pci 0000:01:06.0: supports D2 pci 0000:01:06.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:06.0: PME# disabled PCI: 0000:01:06.1 reg 10 32bit mmio: [90200000, 90200fff] pci 0000:01:06.1: supports D1 pci 0000:01:06.1: supports D2 pci 0000:01:06.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:06.1: PME# disabled PCI: 0000:01:06.3 reg 10 32bit mmio: [90280000, 90280fff] pci 0000:01:06.3: supports D1 pci 0000:01:06.3: supports D2 pci 0000:01:06.3: PME# supported from D0 D1 D2 D3hot pci 0000:01:06.3: PME# disabled PCI: 0000:01:0d.0 reg 10 32bit mmio: [90300000, 903007ff] PCI: 0000:01:0d.0 reg 14 32bit mmio: [90000000, 90003fff] pci 0000:01:0d.0: supports D1 pci 0000:01:0d.0: supports D2 pci 0000:01:0d.0: PME# supported from D0 D1 D2 D3hot pci 0000:01:0d.0: PME# disabled PCI: 0000:01:0e.0 reg 10 32bit mmio: [90080000, 90081fff] pci 0000:01:0e.0: supports D1 pci 0000:01:0e.0: supports D2 pci 0000:01:0e.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:0e.0: PME# disabled pci 0000:00:1e.0: transparent bridge PCI: bridge 0000:00:1e.0 32bit mmio: [90000000, 903fffff] bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C045.C057._PRT] ACPI: PCI Interrupt Link [C0C2] (IRQs *10 11) ACPI: PCI Interrupt Link [C0C3] (IRQs 10 *11) ACPI: PCI Interrupt Link [C0C4] (IRQs *10 11) ACPI: PCI Interrupt Link [C0C5] (IRQs *10 11) ACPI: PCI Interrupt Link [C0C6] (IRQs 10 *11) ACPI: PCI Interrupt Link [C0C7] (IRQs 10 *11) ACPI: PCI Interrupt Link [C0C8] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [C0C9] (IRQs *10 11) ACPI: Power Resource [C171] (on) ACPI: Power Resource [C141] (on) ACPI: Power Resource [C188] (on) ACPI: Power Resource [C18F] (on) ACPI: Power Resource [C199] (on) ACPI: Power Resource [C0E6] (on) ACPI: Power Resource [C1FE] (off) ACPI: Power Resource [C1FF] (off) ACPI: Power Resource [C200] (off) ACPI: Power Resource [C201] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 15 devices ACPI: ACPI bus type pnp unregistered PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default ACPI: RTC can wake from S4 system 00:00: iomem range 0x0-0x9ffff could not be reserved system 00:00: iomem range 0xe0000-0xfffff could not be reserved system 00:00: iomem range 0x100000-0x1f7fffff could not be reserved system 00:0c: ioport range 0x140-0x14f has been reserved system 00:0c: iomem range 0xffb00000-0xffbfffff has been reserved system 00:0c: iomem range 0xfff00000-0xffffffff has been reserved system 00:0d: ioport range 0x4d0-0x4d1 has been reserved system 00:0d: ioport range 0x1000-0x107f has been reserved system 00:0d: ioport range 0x1100-0x113f has been reserved system 00:0d: ioport range 0x1200-0x121f has been reserved system 00:0d: iomem range 0xfec00000-0xfec000ff has been reserved system 00:0d: iomem range 0xfec10000-0xfec1ffff has been reserved system 00:0e: iomem range 0xfec01000-0xfec01fff has been reserved pci 0000:01:06.0: CardBus bridge, secondary bus 0000:02 pci 0000:01:06.0: IO window: 0x003000-0x0030ff pci 0000:01:06.0: IO window: 0x003400-0x0034ff pci 0000:01:06.0: PREFETCH window: 0x20000000-0x23ffffff pci 0000:01:06.0: MEM window: 0x2c000000-0x2fffffff pci 0000:01:06.1: CardBus bridge, secondary bus 0000:03 pci 0000:01:06.1: IO window: 0x003800-0x0038ff pci 0000:01:06.1: IO window: 0x003c00-0x003cff pci 0000:01:06.1: PREFETCH window: 0x24000000-0x27ffffff pci 0000:01:06.1: MEM window: 0x30000000-0x33ffffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1e.0: IO window: 0x3000-0x3fff pci 0000:00:1e.0: MEM window: 0x90000000-0x903fffff pci 0000:00:1e.0: PREFETCH window: 0x00000020000000-0x00000027ffffff pci 0000:00:1e.0: setting latency timer to 64 pci 0000:01:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pci 0000:01:06.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffff] bus: 01 index 0 io port: [3000, 3fff] bus: 01 index 1 mmio: [90000000, 903fffff] bus: 01 index 2 mmio: [20000000, 27ffffff] bus: 01 index 3 io port: [0, ffff] bus: 01 index 4 mmio: [0, ffffffff] bus: 02 index 0 io port: [3000, 30ff] bus: 02 index 1 io port: [3400, 34ff] bus: 02 index 2 mmio: [20000000, 23ffffff] bus: 02 index 3 mmio: [2c000000, 2fffffff] bus: 03 index 0 io port: [3800, 38ff] bus: 03 index 1 io port: [3c00, 3cff] bus: 03 index 2 mmio: [24000000, 27ffffff] bus: 03 index 3 mmio: [30000000, 33ffffff] NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 Unpacking initramfs... done Freeing initrd memory: 709k freed apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 989 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:00:02.0: Boot video device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17 serial 0000:00:1f.6: PCI INT B disabled input: Macintosh mouse button emulation as /class/input/input0 PNP: PS/2 Controller [PNP0303:C196,PNP0f13:C197] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered NET: Registered protocol family 17 Using IPI No-Shortcut mode registered taskstats version 1 Freeing unused kernel memory: 288k freed No dock devices found. input: AT Translated Set 2 keyboard as /class/input/input1 SCSI subsystem initialized libata version 3.00 loaded. pata_acpi 0000:00:1f.1: enabling device (0005 -> 0007) pata_acpi 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pata_acpi 0000:00:1f.1: setting latency timer to 64 pata_acpi 0000:00:1f.1: PCI INT A disabled ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x2c20 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2c28 irq 15 Switched to high resolution mode on CPU 0 ata1.00: ATA-6: TOSHIBA MK1234GAX, AC001A, max UDMA/100 ata1.00: 234441648 sectors, multi 16: LBA48 ata1.00: configured for UDMA/100 ata2.00: ATAPI: SD-R2512, 1A04, max MWDMA2 ata2.00: configured for MWDMA2 scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1234GA AC00 PQ: 0 ANSI: 5 scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-R2512 1A04 PQ: 0 ANSI: 5 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 16, io base 0x000028c0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after Driver 'sd' needs updating - please use bus_type methods sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 <<4>Driver 'sr' needs updating - please use bus_type methods sda5 > sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0x90500000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 19, io base 0x000028e0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002c00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. usb 1-2: new low speed USB device using uhci_hcd and address 2 usb 1-2: configuration #1 chosen from 1 choice rtc_cmos 00:09: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k b44 0000:01:0e.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 ssb: Sonics Silicon Backplane found on PCI device 0000:01:0e.0 b44.c:v2.0 eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:08:02:df:c3:cf ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2 ipw2100: Copyright(c) 2003-2006 Intel Corporation ipw2100 0000:01:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 ipw2100: Detected Intel PRO/Wireless 2100 Network Connection firmware: requesting ipw2100-1.3.fw ipw2100: eth1: Firmware 'ipw2100-1.3.fw' not available or load failed. ipw2100: eth1: ipw2100_get_firmware failed: -2 ipw2100: eth1: Failed to power on the adapter. ipw2100: eth1: Failed to start the firmware. ipw2100Error calling register_netdev. ipw2100 0000:01:04.0: PCI INT A disabled ipw2100: probe of 0000:01:04.0 failed with error -5 Intel ICH 0000:00:1f.5: power state changed by ACPI to D0 Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Intel ICH 0000:00:1f.5: setting latency timer to 64 intel8x0_measure_ac97_clock: measured 52767 usecs intel8x0: clocking to 48000 Intel ICH Modem 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Intel ICH Modem 0000:00:1f.6: setting latency timer to 64 ACPI: AC Adapter [C139] (on-line) ACPI: Battery Slot [C13B] (battery present) ACPI: Battery Slot [C13A] (battery absent) input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input3 ACPI: Sleep Button (CM) [C13D] input: Lid Switch as /class/input/input4 ACPI: Lid Switch [C13C] ACPI: Transitioning device [C202] to D3 fan PNP0C0B:00: registered as cooling_device0 ACPI: Fan [C202] (off) ACPI: Transitioning device [C203] to D3 fan PNP0C0B:01: registered as cooling_device1 ACPI: Fan [C203] (off) ACPI: Transitioning device [C204] to D3 fan PNP0C0B:02: registered as cooling_device2 ACPI: Fan [C204] (off) ACPI: Transitioning device [C205] to D3 fan PNP0C0B:03: registered as cooling_device3 ACPI: Fan [C205] (off) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device4 ACPI: Processor [CPU0] (supports 8 throttling states) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [TZ1] (43 C) thermal LNXTHERM:02: registered as thermal_zone1 ACPI: Thermal Zone [TZ2] (43 C) thermal LNXTHERM:03: registered as thermal_zone2 ACPI: Thermal Zone [TZ3] (25 C) Marking TSC unstable due to TSC halts in idle Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 855GM Chipset agpgart-intel 0000:00:00.0: detected 8060K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0x98000000 ACPI: WMI: Mapper loaded input: Video Bus as /class/input/input5 ACPI: Video Device [C046] (multi-head: yes rom: no post: no) usbcore: registered new interface driver hiddev input: A4Tech USB Optical Mouse as /class/input/input6 input,hidraw0: USB HID v1.10 Mouse [A4Tech USB Optical Mouse] on usb-0000:00:1d.0-2 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver parport_pc 00:05: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 intel_rng: FWH not detected iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) Yenta: CardBus bridge found at 0000:01:06.0 [103c:08bc] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:01:06.0, mfunc 0x012c1202, devctl 0x64 Yenta: ISA IRQ mask 0x0c38, PCI irq 18 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff cs: IO port probe 0x3000-0x3fff: clean. pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff input: PC Speaker as /class/input/input7 tifm_7xx1 0000:01:06.3: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ohci1394 0000:01:0d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 NET: Registered protocol family 23 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[90300000-903007ff] Max Packet=[2048] IR/IT contexts=[4/8] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000 serio: Synaptics pass-through port at isa0060/serio4/input0 Yenta: CardBus bridge found at 0000:01:06.1 [103c:08bc] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:01:06.1, mfunc 0x012c1202, devctl 0x64 input: SynPS/2 Synaptics TouchPad as /class/input/input8 Detected unconfigured HP nx5000 family SMSC IrDA chip, pre-configuring device. Setting up Intel 82801 controller and SMSC device found SMC SuperIO Chip (devid=0x5a rev=00 base=0x004e): LPC47N227 smsc_superio_flat(): fir: 0x130, sir: 0x2f8, dma: 03, irq: 5, mode: 0x0e SMsC IrDA Controller found IrCC version 2.0, firport 0x130, sirport 0x2f8 dma=3, irq=5 No transceiver found. Defaulting to Fast pin select IrDA: Registered device irda0 Error: Driver 'pcspkr' is already registered, aborting... lp0: using parport0 (interrupt-driven). Yenta: ISA IRQ mask 0x0c38, PCI irq 18 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#01) from #03 to #06 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff cs: IO port probe 0x3000-0x3fff: clean. pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff ppdev: user-space parallel port driver Error: Driver 'pcspkr' is already registered, aborting... cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. ieee1394: Host added: ID:BUS[0-00:1023] GUID[718b5000293111a3] EXT3 FS on sda1, internal journal fuse init (API version 7.9) Adding 1020116k swap on /dev/sda3. Priority:-1 extents:1 across:1020116k