on 2.0 ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 16 ata1: SATA max UDMA/100 cmd 0xF8802080 ctl 0xF880208A bmdma 0xF8802000 irq 16 ata2: SATA max UDMA/100 cmd 0xF88020C0 ctl 0xF88020CA bmdma 0xF8802008 irq 16 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-6, max UDMA/133, 156301488 sectors: LBA ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) Vendor: ATA Model: WDC WD800JD-00HK Rev: 13.0 Type: Direct-Access ANSI SCSI revision: 05 ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 17 ata3: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma 0xF8804000 irq 17 ata4: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma 0xF8804008 irq 17 scsi2 : sata_sil ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata3.00: ATA-7, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32) ata3.00: ata3: dev 0 multi count 16 ata3.00: configured for UDMA/100 scsi3 : sata_sil ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata4.00: ATA-6, max UDMA/100, 234441648 sectors: LBA48 ata4.00: ata4: dev 0 multi count 16 ata4.00: applying bridge limits ata4.00: configured for UDMA/100 Vendor: ATA Model: WDC WD1600JS-55N Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: WDC WD1200JD-00G Rev: 02.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 > sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sd 2:0:0:0: Attached scsi disk sdb SCSI device sdc: 234441648 512-byte hdwr sectors (120034 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdc: 234441648 512-byte hdwr sectors (120034 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back sdc: sdc2 sd 3:0:0:0: Attached scsi disk sdc sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: Attached scsi generic sg1 type 0 sd 3:0:0:0: Attached scsi generic sg2 type 0 ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 18 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: EHCI Host Controller drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.2: reset hcs_params 0x102486 dbg=1 cc=2 pcc=4 !ppc ports=6 ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0 ehci_hcd 0000:00:02.2: reset hcc_params a086 caching frame 256/512/1024 park ehci_hcd 0000:00:02.2: park 0 ehci_hcd 0000:00:02.2: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: supports USB remote wakeup ehci_hcd 0000:00:02.2: irq 18, io mem 0xe6005000 ehci_hcd 0000:00:02.2: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.18 ehci_hcd usb usb1: SerialNumber: 0000:00:02.2 usb usb1: uevent usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on non-switchable hub hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 ehci_hcd 0000:00:02.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 19 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller drivers/usb/core/inode.c: creating file '002' ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: created debug files ohci_hcd 0000:00:02.0: irq 19, io mem 0xe6001000 ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600 ohci_hcd 0000:00:02.0: OHCI controller state ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3 ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH ohci_hcd 0000:00:02.0: hcca frame #0003 ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3(3) ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.18 ohci_hcd usb usb2: SerialNumber: 0000:00:02.0 usb usb2: uevent usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: trying to enable port power on non-switchable hub hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 drivers/usb/core/inode.c: creating file '001' ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 20 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: OHCI Host Controller drivers/usb/core/inode.c: creating file '003' ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:02.1: created debug files ohci_hcd 0000:00:02.1: irq 20, io mem 0xe6002000 ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600 ehci_hcd 0000:00:02.2: port 1 high speed ehci_hcd 0000:00:02.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT ohci_hcd 0000:00:02.1: OHCI controller state ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3 ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:02.1: intrstatus 0x00000004 SF ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH ohci_hcd 0000:00:02.1: hcca frame #0003 ohci_hcd 0000:00:02.1: roothub.a 01000203 POTPGT=1 NPS NDP=3(3) ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS usb usb3: default language 0x0409 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.18 ohci_hcd usb usb3: SerialNumber: 0000:00:02.1 usb usb3: uevent usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: global over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: no over-current condition exists hub 3-0:1.0: trying to enable port power on non-switchable hub usb 1-1: new high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:02.2: port 1 high speed ehci_hcd 0000:00:02.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT drivers/usb/core/inode.c: creating file '001' USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... ohci_hcd 0000:00:02.0: suspend root hub usb 1-1: default language 0x0409 usb 1-1: new device strings: Mfr=138, Product=154, SerialNumber=168 usb 1-1: Product: External HDD usb 1-1: Manufacturer: Western Digital usb 1-1: SerialNumber: 5743414C4132313830323539 usb 1-1: uevent usb 1-1: configuration #1 chosen from 1 choice usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: uevent drivers/usb/core/inode.c: creating file '002' ehci_hcd 0000:00:02.2: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s ohci_hcd 0000:00:02.1: suspend root hub hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:02.2: port 3 low speed --> companion ehci_hcd 0000:00:02.2: GetStatus port 3 status 003402 POWER OWNER sig=k CSC hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 3 chg 0000 evt 0000, resume root ohci_hcd 0000:00:02.1: wakeup hub 3-0:1.0: state 7 ports 3 chg 0000 evt 0000 usb-storage 1-1:1.0: usb_probe_interface usb-storage 1-1:1.0: usb_probe_interface - got id ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS hub 3-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s scsi4 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS usb 3-1: new low speed USB device using ohci_hcd and address 2 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS usb 3-1: skipped 1 descriptor after interface usb 3-1: skipped 1 descriptor after interface usb 3-1: default language 0x0409 usb 3-1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-1: Product: USB Receiver usb 3-1: Manufacturer: Logitech usb 3-1: uevent usb 3-1: configuration #1 chosen from 1 choice usb 3-1: adding 3-1:1.0 (config #1, interface 0) usb 3-1:1.0: uevent usb 3-1: adding 3-1:1.1 (config #1, interface 1) usb 3-1:1.1: uevent drivers/usb/core/inode.c: creating file '002' hub 3-0:1.0: state 7 ports 3 chg 0000 evt 0002 usbhid 3-1:1.0: usb_probe_interface usbhid 3-1:1.0: usb_probe_interface - got id input: Logitech USB Receiver as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.1-1 usbhid 3-1:1.1: usb_probe_interface usbhid 3-1:1.1: usb_probe_interface - got id input: Logitech USB Receiver as /class/input/input1 input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-1 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice ts: Compaq touchscreen protocol output I2O subsystem v1.325 i2o: max drivers = 8 i2c /dev entries driver ip_conntrack version 2.4 (7168 buckets, 57344 max) - 172 bytes per conntrack ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode Time: tsc clocksource has been installed. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: sda7: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 16328 ext3_orphan_cleanup: deleting unreferenced inode 16327 ext3_orphan_cleanup: deleting unreferenced inode 16326 ext3_orphan_cleanup: deleting unreferenced inode 16325 ext3_orphan_cleanup: deleting unreferenced inode 16324 EXT3-fs: sda7: 5 orphan inodes deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 140k freed usb 3-1:1.1: uevent usb 3-1:1.0: uevent usb 3-1: uevent usb 1-1:1.0: uevent usb 1-1: uevent usb 3-0:1.0: uevent usb usb3: uevent usb 2-0:1.0: uevent usb usb2: uevent usb 1-0:1.0: uevent usb usb1: uevent forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 18 PCI: Setting latency timer of device 0000:00:04.0 to 64 eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0 Vendor: WD Model: 1200BB External Rev: 0412 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB) sdd: Write Protect is off sdd: Mode Sense: 33 00 00 00 sdd: assuming drive cache: write through SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB) sdd: Write Protect is off sdd: Mode Sense: 33 00 00 00 sdd: assuming drive cache: write through sdd: sdd1 sd 4:0:0:0: Attached scsi disk sdd sd 4:0:0:0: Attached scsi generic sg3 type 0 usb-storage: device scan complete EXT3 FS on sda7, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS volume version 3.1. Adding 722884k swap on /dev/sda5. Priority:-1 extents:1 across:722884k