Linux version 2.6.27-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Sun Oct 26 10:08:01 UTC 2008 Command line: root=/dev/sda1 ro vga=795 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bffa0000 (usable) BIOS-e820: 00000000bffa0000 - 00000000bffae000 (ACPI data) BIOS-e820: 00000000bffae000 - 00000000bffe0000 (ACPI NVS) BIOS-e820: 00000000bffe0000 - 00000000c0000000 (reserved) BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) last_pfn = 0xbffa0 max_arch_pfn = 0x3ffffffff x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 init_memory_mapping 0000000000 - 00bfe00000 page 2M 00bfe00000 - 00bffa0000 page 4k kernel direct mapping tables up to bffa0000 @ 8000-d000 last_map_addr: bffa0000 end: bffa0000 RAMDISK: 37f31000 - 37fef192 DMI 2.3 present. ACPI: RSDP 000FACD0, 0024 (r2 ACPIAM) ACPI: XSDT BFFA0100, 0044 (r1 A M I OEMXSDT 8000624 MSFT 97) ACPI: FACP BFFA0290, 00F4 (r3 A M I OEMFACP 8000624 MSFT 97) ACPI: DSDT BFFA0400, 8186 (r1 A0227 A0227000 0 INTL 2002026) ACPI: FACS BFFAE000, 0040 ACPI: APIC BFFA0390, 0070 (r1 A M I OEMAPIC 8000624 MSFT 97) ACPI: OEMB BFFAE040, 0066 (r1 A M I AMI_OEM 8000624 MSFT 97) ACPI: MCFG BFFA8590, 003C (r1 A M I OEMMCFG 8000624 MSFT 97) (6 early reservations) ==> bootmem [0000000000 - 00bffa0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 00006dea4c] TEXT DATA BSS ==> [0000200000 - 00006dea4c] #3 [0037f31000 - 0037fef192] RAMDISK ==> [0037f31000 - 0037fef192] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] #5 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000] found SMP MP-table at [ffff8800000ff780] 000ff780 [ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x000bffa0 On node 0 totalpages: 786239 DMA zone: 2593 pages, LIFO batch:0 DMA32 zone: 771545 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information SMP: Allowing 2 CPUs, 0 hotplug CPUs PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000 PM: Registered nosave memory: 00000000000e4000 - 0000000000100000 Allocating PCI resources starting at c4000000 (gap: c0000000:3fb80000) PERCPU: Allocating 47648 bytes of per cpu data NR_CPUS: 16, nr_cpu_ids: 2, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 774138 Kernel command line: root=/dev/sda1 ro vga=795 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) TSC: PIT calibration confirmed by PMTIMER. TSC: using PMTIMER calibration value Detected 2676.076 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... No AGP bridge found Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! Memory: 3089108k/3145344k available (2526k kernel code, 55204k reserved, 1038k data, 336k init) CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 5354.15 BogoMIPS (lpj=8920253) Security Framework initialized Mount-cache hash table entries: 256 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM1) using mwait in idle threads. ACPI: Core revision 20080609 ACPI: Checking initramfs for custom DSDT ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) D CPU 2.66GHz stepping 07 Using local APIC timer interrupts. APIC timer calibration result 8362725 Detected 8.362 MHz APIC timer. Booting processor 1/1 ip 6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5354.17 BogoMIPS (lpj=8920278) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM1) x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Pentium(R) D CPU 2.66GHz stepping 07 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (10708.33 BogoMIPS). net_namespace: 1536 bytes Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support. PCI: Using configuration type 1 for base access ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled PCI: 0000:00:1b.0 reg 10 64bit mmio: [cecf8000, cecfbfff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold pci 0000:00:1c.3: PME# disabled PCI: 0000:00:1d.0 reg 20 io port: [7000, 701f] PCI: 0000:00:1d.1 reg 20 io port: [7400, 741f] PCI: 0000:00:1d.2 reg 20 io port: [7800, 781f] PCI: 0000:00:1d.3 reg 20 io port: [8000, 801f] PCI: 0000:00:1d.7 reg 10 32bit mmio: [cecff800, cecffbff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO PCI: 0000:00:1f.1 reg 10 io port: [0, 7] PCI: 0000:00:1f.1 reg 14 io port: [0, 3] PCI: 0000:00:1f.1 reg 18 io port: [0, 7] PCI: 0000:00:1f.1 reg 1c io port: [0, 3] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf] PCI: 0000:00:1f.2 reg 10 io port: [9800, 9807] PCI: 0000:00:1f.2 reg 14 io port: [9400, 9403] PCI: 0000:00:1f.2 reg 18 io port: [9000, 9007] PCI: 0000:00:1f.2 reg 1c io port: [8800, 8803] PCI: 0000:00:1f.2 reg 20 io port: [8400, 840f] PCI: 0000:00:1f.2 reg 24 32bit mmio: [cecffc00, cecfffff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled PCI: 0000:00:1f.3 reg 20 io port: [400, 41f] PCI: 0000:04:00.0 reg 10 32bit mmio: [d0000000, dfffffff] PCI: 0000:04:00.0 reg 18 64bit mmio: [cefe0000, cefeffff] PCI: 0000:04:00.0 reg 20 io port: [e000, e0ff] PCI: 0000:04:00.0 reg 30 32bit mmio: [cefc0000, cefdffff] pci 0000:04:00.0: supports D1 pci 0000:04:00.0: supports D2 PCI: 0000:04:00.1 reg 10 64bit mmio: [ceff0000, ceffffff] pci 0000:04:00.1: supports D1 pci 0000:04:00.1: supports D2 PCI: bridge 0000:00:01.0 io port: [e000, efff] PCI: bridge 0000:00:01.0 32bit mmio: [cef00000, ceffffff] PCI: bridge 0000:00:01.0 64bit mmio pref: [d0000000, dfffffff] PCI: bridge 0000:00:1c.0 io port: [d000, dfff] PCI: 0000:02:00.0 reg 10 64bit mmio: [ceefc000, ceefffff] PCI: 0000:02:00.0 reg 18 io port: [c800, c8ff] PCI: 0000:02:00.0 reg 30 32bit mmio: [ceec0000, ceedffff] pci 0000:02:00.0: supports D1 pci 0000:02:00.0: supports D2 pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:00.0: PME# disabled PCI: bridge 0000:00:1c.3 io port: [c000, cfff] PCI: bridge 0000:00:1c.3 32bit mmio: [cee00000, ceefffff] PCI: 0000:01:01.0 reg 10 32bit mmio: [cfffe000, cfffefff] PCI: 0000:01:01.1 reg 10 32bit mmio: [cffff000, cfffffff] PCI: 0000:01:03.0 reg 10 io port: [b800, b807] PCI: 0000:01:03.0 reg 14 io port: [b400, b403] PCI: 0000:01:03.0 reg 18 io port: [b000, b007] PCI: 0000:01:03.0 reg 1c io port: [a800, a803] PCI: 0000:01:03.0 reg 20 io port: [a400, a40f] PCI: 0000:01:03.0 reg 30 32bit mmio: [cede0000, cedfffff] pci 0000:00:1e.0: transparent bridge PCI: bridge 0000:00:1e.0 io port: [a000, bfff] PCI: bridge 0000:00:1e.0 32bit mmio: [ced00000, cedfffff] PCI: bridge 0000:00:1e.0 64bit mmio pref: [cff00000, cfffffff] bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 33, should be 26 [20080609] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI-GART: No AMD northbridge found. hpet clockevent registered ACPI: RTC can wake from S4 system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved system 00:08: ioport range 0x290-0x297 has been reserved system 00:09: ioport range 0x4d0-0x4d1 has been reserved system 00:09: ioport range 0x800-0x87f has been reserved system 00:09: ioport range 0x480-0x4bf has been reserved system 00:09: ioport range 0x900-0x90f has been reserved system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved system 00:0d: iomem range 0x0-0x9ffff could not be reserved system 00:0d: iomem range 0xc0000-0xdffff has been reserved system 00:0d: iomem range 0xe0000-0xfffff could not be reserved system 00:0d: iomem range 0x100000-0xbfffffff could not be reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:04 pci 0000:00:01.0: IO window: 0xe000-0xefff pci 0000:00:01.0: MEM window: 0xcef00000-0xceffffff pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03 pci 0000:00:1c.0: IO window: 0xd000-0xdfff pci 0000:00:1c.0: MEM window: disabled pci 0000:00:1c.0: PREFETCH window: disabled pci 0000:00:1c.3: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.3: IO window: 0xc000-0xcfff pci 0000:00:1c.3: MEM window: 0xcee00000-0xceefffff pci 0000:00:1c.3: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1e.0: IO window: 0xa000-0xbfff pci 0000:00:1e.0: MEM window: 0xced00000-0xcedfffff pci 0000:00:1e.0: PREFETCH window: 0x000000cff00000-0x000000cfffffff pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 pci 0000:00:1c.3: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 io port: [e000, efff] bus: 04 index 1 mmio: [cef00000, ceffffff] bus: 04 index 2 mmio: [d0000000, dfffffff] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 io port: [d000, dfff] bus: 03 index 1 mmio: [0, 0] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 02 index 0 io port: [c000, cfff] bus: 02 index 1 mmio: [cee00000, ceefffff] bus: 02 index 2 mmio: [0, 0] bus: 02 index 3 mmio: [0, 0] bus: 01 index 0 io port: [a000, bfff] bus: 01 index 1 mmio: [ced00000, cedfffff] bus: 01 index 2 mmio: [cff00000, cfffffff] bus: 01 index 3 io port: [0, ffff] bus: 01 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 Unpacking initramfs... done Freeing initrd memory: 760k freed VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) msgmni has been set to 6036 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:04:00.0: Boot video device pcieport-driver 0000:00:01.0: setting latency timer to 64 pcieport-driver 0000:00:01.0: found MSI capability pci_express 0000:00:01.0:pcie00: allocate port service pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pcieport-driver 0000:00:1c.3: setting latency timer to 64 pcieport-driver 0000:00:1c.3: found MSI capability pci_express 0000:00:1c.3:pcie00: allocate port service vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000080000, using 10240k, total 16384k vesafb: mode is 1280x1024x32, linelength=5120, pages=2 vesafb: scrolling: redraw vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device Linux agpgart interface v0.103 Serial: 8250/16550 driver4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A input: Macintosh mouse button emulation as /class/input/input0 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered NET: Registered protocol family 17 registered taskstats version 1 Freeing unused kernel memory: 336k freed No dock devices found. SCSI subsystem initialized libata version 3.00 loaded. pata_it821x 0000:01:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 pata_it821x: controller in pass through mode. pata_it821x 0000:01:03.0: setting latency timer to 64 scsi0 : pata_it821x scsi1 : pata_it821x ata1: PATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xa400 irq 20 ata2: PATA max UDMA/133 cmd 0xb000 ctl 0xa800 bmdma 0xa408 irq 20 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ata1.00: ATA-7: SAMSUNG SP2014N, VC100-33, max UDMA/100 ata1.00: 390721968 sectors, multi 0: LBA48 ata1.00: configured for UDMA/100 isa bounce pool size: 16 pages scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2014N VC10 PQ: 0 ANSI: 5 ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata3.00: ATAPI: HL-DT-ST DVDRAM GSA-4160B, A300, max UDMA/66 ata3.00: limited to UDMA/33 due to 40-wire cable ata3.00: configured for UDMA/33 scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4160B A300 PQ: 0 ANSI: 5 ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ata_piix 0000:00:1f.2: setting latency timer to 64 scsi4 : ata_piix scsi5 : ata_piix ata5: SATA max UDMA/133 cmd 0x9800 ctl 0x9400 bmdma 0x8400 irq 23 ata6: SATA max UDMA/133 cmd 0x9000 ctl 0x8800 bmdma 0x8408 irq 23 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Driver 'sr' needs updating - please use bus_type methods USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 2:0:0:0: Attached scsi CD-ROM sr0 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00007000 Driver 'sd' needs updating - please use bus_type methods sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sd 0:0:0:0: [sda] Attached SCSI disk usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 17, io base 0x00007400 usb usb2: configuration #1 chosen from 1 choice usb 1-1: new low speed USB device using uhci_hcd and address 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller usb 1-1: configuration #1 chosen from 1 choice uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00007800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 19, io base 0x00008000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported ehci_hcd 0000:00:1d.7: irq 20, io mem 0xcecff800 usbcore: registered new interface driver hiddev ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb 1-1: USB disconnect, address 2 usbcore: registered new interface driver usbhid usb usb5: configuration #1 chosen from 1 choice usbhid: v2.6:USB HID core driver hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected JFS: nTxBlock = 8192, nTxLock = 65536 usb 1-1: new low speed USB device using uhci_hcd and address 3 usb 1-1: configuration #1 chosen from 1 choice input: Microsft Microsoft Wireless Desktop Receiver 3.1 as /class/input/input1 input,hidraw0: USB HID v1.11 Keyboard [Microsft Microsoft Wireless Desktop Receiver 3.1] on usb-0000:00:1d.0-1 Fixing up Microsoft Wireless Receiver Model 1028 report descriptor input: Microsft Microsoft Wireless Desktop Receiver 3.1 as /class/input/input2 input,hidraw1: USB HID v1.11 Mouse [Microsft Microsoft Wireless Desktop Receiver 3.1] on usb-0000:00:1d.0-1 rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, hpet irqs sky2 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 sky2 0000:02:00.0: setting latency timer to 64 sky2 0000:02:00.0: v1.22 addr 0xceefc000 irq 19 Yukon-2 EC rev 2 sky2 eth0: addr 00:18:f3:5b:b3:35 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 HDA Intel 0000:00:1b.0: setting latency timer to 64 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... Bt87x 0000:01:01.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21 bt87x0: Using board 1, analog, digital (rate 32000 Hz) fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. Symbol init_mm is marked as UNUSED, however this module is using it. This symbol will go away in the future. Please evalute if this is the right api to use and if it really is, submit a report the linux kernel mailinglist together with submitting your code for inclusion. [fglrx] Maximum main memory to use for locked dma buffers: 2872 MBytes. [fglrx] vendor: 1002 device: 7142 count: 1 [fglrx] ioport: bar 4, base 0xe000, size: 0x100 pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:04:00.0: setting latency timer to 64 [fglrx] Pat entry 2 is already configured [fglrx] PAT is enabled successfully! [fglrx] module loaded - fglrx 8.52.3 [Aug 1 2008] with 1 minors fuse init (API version 7.9) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) processor ACPI0007:01: registered as cooling_device1 ACPI: Processor [CPU2] (supports 8 throttling states) sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 2:0:0:0: Attached scsi generic sg1 type 5 parport_pc 00:07: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) intel_rng: FWH not detected i801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23 ACPI: I/O resource 0000:00:1f.3 [0x400-0x41f] conflicts with ACPI region SMRG [0x400-0x40f] ACPI: Device needs an ACPI driver input: PC Speaker as /class/input/input5 PPP generic driver version 2.4.2 Error: Driver 'pcspkr' is already registered, aborting... ppdev: user-space parallel port driver lp0: using parport0 (interrupt-driven). Error: Driver 'pcspkr' is already registered, aborting... Linux video capture interface: v2.00 bttv: driver version 0.9.17 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv 0000:01:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 bttv0: Bt878 (rev 17) at 0000:01:01.0, irq: 21, latency: 64, mmio: 0xcfffe000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] tveeprom 1-0050: Hauppauge model 44854, rev D147, serial# 1111158 tveeprom 1-0050: tuner model is LG TP18PSB01D (idx 47, type 28) tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) tveeprom 1-0050: audio processor is MSP3415 (idx 6) tveeprom 1-0050: has radio bttv0: Hauppauge eeprom indicates model#44854 bttv0: tuner type=28 bttv0: i2c: checking for MSP34xx @ 0x80... found msp3400' 1-0040: MSP3415G-B8 found @ 0x80 (bt878 #0 [sw]) msp3400' 1-0040: msp3400 supports nicam and radio, mode is autodetect and autoselect bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found tuner' 1-0061: chip found @ 0xc2 (bt878 #0 [sw]) tuner-simple 1-0061: creating new instance tuner-simple 1-0061: type set to 28 (LG PAL_BG+FM (TPI8PSB01D)) bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok Adding 1461872k swap on /dev/sda7. Priority:-1 extents:1 across:1461872k sky2 eth0: enabling interface sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both w83627ehf: Found W83627EHG chip at 0x290 [fglrx] Reserved FB block: Shared offset:0, size:1000000 [fglrx] Reserved FB block: Unshared offset:7ffb000, size:5000 [fglrx] Reserved FB block: Unshared offset:ffbf000, size:40000 [fglrx] Reserved FB block: Unshared offset:ffff000, size:1000 NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth0: no IPv6 routers present totem-video-ind[3591]: segfault at 8 ip 00007f04aba60386 sp 00007fffb451bc20 error 4 in libgstreamer-0.10.so.0.18.0[7f04ab9d6000+c2000] totem-video-ind[3613]: segfault at 8 ip 00007f6f2390b386 sp 00007fff2c3c6ad0 error 4 in libgstreamer-0.10.so.0.18.0[7f6f23881000+c2000] totem-video-ind[3656]: segfault at 8 ip 00007ffb1ff81386 sp 00007fff28a3d140 error 4 in libgstreamer-0.10.so.0.18.0[7ffb1fef7000+c2000]