Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.1 20080724 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Aug 26 21:15:43 UTC 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001ffb0000 (usable)
 BIOS-e820: 000000001ffb0000 - 000000001ffc0000 (ACPI data)
 BIOS-e820: 000000001ffc0000 - 000000001fff0000 (ACPI NVS)
 BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Entering add_active_range(0, 0, 130992) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   130992
  HighMem    130992 ->   130992
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   130992
On node 0 totalpages: 130992
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 992 pages used for memmap
  Normal zone: 125904 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F8EC0, 0014 (r0 ACPIAM)
ACPI: RSDT 1FFB0000, 0030 (r1 A M I  OEMRSDT   7000631 MSFT       97)
ACPI: FACP 1FFB0200, 0081 (r2 A M I  OEMFACP   7000631 MSFT       97)
ACPI: DSDT 1FFB03E0, 4104 (r1  K7NF2 K7NF2112      112 INTL  2002026)
ACPI: FACS 1FFC0000, 0040
ACPI: APIC 1FFB0390, 004A (r1 A M I  OEMAPIC   7000631 MSFT       97)
ACPI: OEMB 1FFC0040, 0041 (r1 A M I  NVD_CRB   7000631 MSFT       97)
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
SMP: Allowing 1 CPUs, 0 hotplug CPUs
PERCPU: Allocating 39464 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129968
Kernel command line: root=/dev/sda3 ro vga=773
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2000.017 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 514344k/523968k available (2120k kernel code, 9064k reserved, 744k data, 264k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee4000 - 0xfffff000   (1132 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdffb0000   ( 511 MB)
      .init : 0xc03d3000 - 0xc0415000   ( 264 kB)
      .data : 0xc031211e - 0xc03cc380   ( 744 kB)
      .text : 0xc0100000 - 0xc031211e   (2120 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 4003.13 BogoMIPS (lpj=6670619)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20080321
ACPI: Checking initramfs for custom DSDT
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) XP 2400+ stepping 01
Brought up 1 CPUs
Total of 1 processors activated (4003.13 BogoMIPS).
net_namespace: 652 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 17) *5
ACPI: PCI Interrupt Link [LNKC] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 19) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 16) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *3
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LAPU] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 23) *5
ACPI: PCI Interrupt Link [LFWR] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LETH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LSHD] (IRQs 20 21 22) *0, disabled.
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 84, should be 76 [20080321]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: iomem range 0xff780000-0xffffffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:0c: ioport range 0x680-0x6ff has been reserved
system 00:0c: ioport range 0x295-0x296 has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x1fffffff could not be reserved
PCI: Bridge: 0000:00:08.0
  IO window: d000-dfff
  MEM window: 0xff500000-0xff5fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: c000-cfff
  MEM window: 0xff400000-0xff4fffff
  PREFETCH window: 0x00000000aeb00000-0x00000000eeafffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 470k freed
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1005
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 1536k, total 262144k
vesafb: mode is 1024x768x8, linelength=1024, pages=254
vesafb: protected mode interface info at c000:5761
vesafb: pmi: set display start = c00c57f5, set palette = c00c5841
vesafb: pmi: ports = c810 c816 c854 c838 c83c c85c c800 c804 c8b0 c8b2 c8b4 
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
input: AT Translated Set 2 keyboard as /class/input/input1
pata_amd 0000:00:09.0: version 0.3.10
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
Switched to high resolution mode on CPU 0
ata1.00: ATA-6: WDC WD800BB-00JHC0, 05.01C05, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA 
ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc600c0c6) ACPI=0x3f01f (17:900:0x11)
ata1.00: configured for UDMA/100
ata2.00: ATAPI: _NEC DVD_RW ND-3520AW, 2.U5, max UDMA/33
ata2.01: ATA-6: WDC WD2000JB-32EVA0, 15.05R15, max UDMA/100
ata2.01: 390721968 sectors, multi 16: LBA48 
ata2: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc600c0c6) ACPI=0x701f (54:17:0x15)
ata2: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc600c0c6) ACPI=0x3f01f (54:17:0x15)
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      WDC WD800BB-00JH 05.0 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            _NEC     DVD_RW ND-3520AW 2.U5 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access     ATA      WDC WD2000JB-32E 15.0 PQ: 0 ANSI: 5
pata_pdc2027x 0000:02:07.0: version 1.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKD] -> GSI 19 (level, high) -> IRQ 19
pata_pdc2027x 0000:02:07.0: PLL input clock 16661 kHz
scsi2 : pata_pdc2027x
scsi3 : pata_pdc2027x
ata3: PATA max UDMA/100 mmio m16384@0xff5f8000 cmd 0xff5f97c0 irq 19
ata4: PATA max UDMA/100 mmio m16384@0xff5f8000 cmd 0xff5f95c0 irq 19
ata3.00: ATA-7: Maxtor 6Y200P0, YAR41BW0, max UDMA/133
ata3.00: 398297088 sectors, multi 16: LBA48 
ata3.01: ATA-6: WDC WD2000JB-00GVC0, 08.02D08, max UDMA/100
ata3.01: 390721968 sectors, multi 16: LBA48 
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata4.00: ATA-6: WDC WD3200JB-00KFA0, 08.05J08, max UDMA/100
ata4.00: 625142448 sectors, multi 16: LBA48 
ata4.01: ATA-4: ST320413A, 3.54, max UDMA/100
ata4.01: 39102336 sectors, multi 16: LBA 
ata4.00: configured for UDMA/100
ata4.01: configured for UDMA/100
scsi 2:0:0:0: Direct-Access     ATA      Maxtor 6Y200P0   YAR4 PQ: 0 ANSI: 5
scsi 2:0:1:0: Direct-Access     ATA      WDC WD2000JB-00G 08.0 PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access     ATA      WDC WD3200JB-00K 08.0 PQ: 0 ANSI: 5
scsi 3:0:1:0: Direct-Access     ATA      ST320413A        3.54 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:1:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
sd 1:0:1:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 398297088 512-byte hardware sectors (203928 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:1:0: [sdd] 390721968 512-byte hardware sectors (200050 MB)
sd 2:0:1:0: [sdd] Write Protect is off
sd 2:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:1:0: [sdd] 390721968 512-byte hardware sectors (200050 MB)
sd 2:0:1:0: [sdd] Write Protect is off
sd 2:0:1:0: [sdd] Mode Sense: 00 3a 00 00
sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdd: sdd1 sdd2 sdd3 sdd4
sd 2:0:1:0: [sdd] Attached SCSI disk
sd 3:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sde] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sde: sde1
sd 3:0:0:0: [sde] Attached SCSI disk
sd 3:0:1:0: [sdf] 39102336 512-byte hardware sectors (20020 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:1:0: [sdf] 39102336 512-byte hardware sectors (20020 MB)
sd 3:0:1:0: [sdf] Write Protect is off
sd 3:0:1:0: [sdf] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdf: sdf1
sd 3:0:1:0: [sdf] Attached SCSI disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 17 (level, high) -> IRQ 17
eth0: RealTek RTL8139 at 0xe0860c00, 00:10:a7:0e:e0:70, IRQ 17
eth0:  Identified 8139 chip type 'RTL-8139C'
fuse init (API version 7.9)
loop: module loaded
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
sd 1:0:1:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: Attached scsi generic sg3 type 0
sd 2:0:1:0: Attached scsi generic sg4 type 0
sd 3:0:0:0: Attached scsi generic sg5 type 0
sd 3:0:1:0: Attached scsi generic sg6 type 0
Linux agpgart interface v0.103
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xf0000000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4300
 : Error requesting region 4300 .. 433F for SMB2
nForce2_smbus 0000:00:01.1: Error probing SMB2.
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 22, io mem 0xff6fb000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 21, io mem 0xff6fc000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 20 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: debug port 0
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 20, io mem 0xff6fdc00
usb 1-1: new low speed USB device using ohci_hcd and address 2
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 1
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LKLN] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:04.0 to 64
forcedeth 0000:00:04.0: ifname eth1, PHY OUI 0x732 @ 1, addr 00:13:8f:c4:e5:de
forcedeth 0000:00:04.0: csum timirq lnktim desc-v2
usb 1-1: new low speed USB device using ohci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
lp: driver loaded but no devices found
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
usb 1-2: new low speed USB device using ohci_hcd and address 4
PPP generic driver version 2.4.2
usb 1-2: configuration #1 chosen from 1 choice
ppdev: user-space parallel port driver
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:06.0 to 64
gameport: NS558 PnP Gameport is pnp00:07/gameport0, io 0x200, speed 59659kHz
intel8x0_measure_ac97_clock: measured 51865 usecs
intel8x0: clocking to 47420
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Symbol init_mm is marked as UNUSED, however this module is using it.
This symbol will go away in the future.
Please evalute if this is the right api to use and if it really is, submit a report the linux kernel mailinglist together with submitting your code for inclusion.
[fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
[fglrx]   vendor: 1002 device: 4153 count: 1
[fglrx] ioport: bar 1, base 0xc800, size: 0x100
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKD] -> GSI 19 (level, high) -> IRQ 19
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.52.3 [Aug  1 2008] with 1 minors
parport_pc 00:06: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
usbcore: registered new interface driver hiddev
input: Dual PSX-USB Adaptor  Dual PSX-USB Adaptor  as /class/input/input4
input: Dual PSX-USB Adaptor  Dual PSX-USB Adaptor  as /class/input/input5
input: Dual PSX-USB Adaptor  Dual PSX-USB Adaptor  as /class/input/input6
input: Dual PSX-USB Adaptor  Dual PSX-USB Adaptor  as /class/input/input7
input,hidraw0: USB HID v1.00 Joystick [Dual PSX-USB Adaptor  Dual PSX-USB Adaptor ] on usb-0000:00:02.0-1
input: Logitech USB-PS/2 Optical Mouse as /class/input/input8
input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
EXT3 FS on sda3, internal journal
Adding 755044k swap on /dev/sda4.  Priority:-1 extents:1 across:755044k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[fglrx] AGP detected, AgpState   = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled,  AgpCommand = 0x1f004312 (selected caps)
[fglrx] Setup AGP aperture
[fglrx] GART Table is not in FRAME_BUFFER range