Linux version 2.6.24-ARCH (root@T-POWA-LX) (gcc version 4.2.3) #1 SMP PREEMPT Wed Mar 5 12:53:18 CET 2008 Command line: root=/dev/sda6 ro quiet vga=791 splash resume=/dev/sda5 cpufreq.debug=7 5 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000007f65b800 (usable) BIOS-e820: 000000007f65b800 - 0000000080000000 (reserved) BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved) BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 521819) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.4 present. ACPI: RSDP 000FBB00, 0024 (r2 DELL ) ACPI: XSDT 7F65D200, 0064 (r1 DELL M08 27D8021C ASL 61) ACPI: FACP 7F65D09C, 00F4 (r4 DELL M08 27D8021C ASL 61) ACPI: DSDT 7F65D800, 63F7 (r2 INT430 SYSFexxx 1001 INTL 20050624) ACPI: FACS 7F66C000, 0040 ACPI: HPET 7F65D300, 0038 (r1 DELL M08 1 ASL 61) ACPI: APIC 7F65D400, 0068 (r1 DELL M08 27D8021C ASL 47) ACPI: ASF! 7F65D000, 007E (r32 DELL M08 27D8021C ASL 61) ACPI: MCFG 7F65D3C0, 003E (r16 DELL M08 27D8021C ASL 61) ACPI: SLIC 7F65D49C, 0176 (r1 DELL M08 27D8021C ASL 61) ACPI: TCPA 7F65D700, 0032 (r1 0 ASL 0) ACPI: SSDT 7F65B9C0, 04CC (r1 PmRef CpuPm 3000 INTL 20050624) ACPI: DMI detected: Dell Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 521819) 1 entries of 256 used No mptable found. Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 521819 On node 0 totalpages: 521722 DMA zone: 56 pages used for memmap DMA zone: 1321 pages reserved DMA zone: 2622 pages, LIFO batch:0 DMA32 zone: 7078 pages used for memmap DMA32 zone: 510645 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 0000000000100000 Allocating PCI resources starting at 88000000 (gap: 80000000:78000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 33200 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513267 Kernel command line: root=/dev/sda6 ro quiet vga=791 splash resume=/dev/sda5 cpufreq.debug=7 5 Unknown boot option `cpufreq.debug=7': ignoring Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Extended CMOS year: 2000 hpet clockevent registered TSC calibrated against HPET Marking TSC unstable due to TSCs unsynchronized time.c: Detected 1994.995 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! Memory: 2043596k/2087276k available (2821k kernel code, 42900k reserved, 1097k data, 252k init) SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 3995.03 BogoMIPS (lpj=6656055) Security Framework initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K using mwait in idle threads. CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) SMP alternatives: switching to UP code Early unpacking initramfs... done ACPI: Core revision 20070126 ACPI: Looking for DSDT in initramfs... successfully read 23806 bytes from /DSDT.aml. ACPI: Table DSDT replaced by host OS ACPI: DSDT 00000000, 5CFE (r2 INT430 SYSFexxx 1001 INTL 20061109) ACPI: DSDT override uses original SSDTs unless "acpi_no_auto_ssdt"<6>Using local APIC timer interrupts. APIC timer calibration result 12468710 Detected 12.468 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3991.24 BogoMIPS (lpj=6649995) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a Brought up 2 CPUs net_namespace: 120 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at f8000000 - fbffffff ACPI: EC: Look up EC in DSDT ACPI: SSDT 7F66C080, 0043 (r1 LMPWR DELLLOM 1001 INTL 20050624) ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1080-10bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10 ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *3 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnpacpi: exceeded the max number of mem resources: 12 pnp: PnP ACPI: found 15 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI-GART: No AMD northbridge found. ACPI: RTC can wake from S4 Time: hpet clocksource has been installed. Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 system 00:05: ioport range 0xc80-0xcaf has been reserved system 00:05: ioport range 0xcc0-0xcff could not be reserved system 00:08: iomem range 0xfed00000-0xfed003ff has been reserved system 00:0b: ioport range 0xcb0-0xcbb has been reserved system 00:0b: iomem range 0xfed40000-0xfed44fff could not be reserved system 00:0c: ioport range 0x900-0x97f has been reserved system 00:0c: ioport range 0x4d0-0x4d1 has been reserved system 00:0c: ioport range 0x1000-0x1005 has been reserved system 00:0c: ioport range 0x1008-0x100f has been reserved system 00:0d: ioport range 0xf400-0xf4fe has been reserved system 00:0d: ioport range 0x1006-0x1007 has been reserved system 00:0d: ioport range 0x100a-0x1059 could not be reserved system 00:0d: ioport range 0x1060-0x107f has been reserved system 00:0d: ioport range 0x1080-0x10bf has been reserved system 00:0d: ioport range 0x10c0-0x10df has been reserved system 00:0d: ioport range 0x1010-0x102f has been reserved system 00:0d: ioport range 0x809-0x809 has been reserved system 00:0e: iomem range 0x0-0x9efff could not be reserved system 00:0e: iomem range 0x9f000-0x9ffff could not be reserved system 00:0e: iomem range 0xc0000-0xcffff has been reserved system 00:0e: iomem range 0xe0000-0xfffff has been reserved system 00:0e: iomem range 0x100000-0x7f6803ff could not be reserved system 00:0e: iomem range 0x7f680400-0x7f6fffff could not be reserved system 00:0e: iomem range 0x7f700000-0x7f7fffff could not be reserved system 00:0e: iomem range 0x7f700000-0x7fefffff could not be reserved system 00:0e: iomem range 0xffe00000-0xffffffff could not be reserved system 00:0e: iomem range 0xffa00000-0xffbfffff has been reserved system 00:0e: iomem range 0xfec00000-0xfec0ffff could not be reserved system 00:0e: iomem range 0xfee00000-0xfee0ffff could not be reserved PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: fe800000-fe8fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: d000-dfff MEM window: fe600000-fe7fffff PREFETCH window: f0000000-f01fffff PCI: Bridge: 0000:00:1c.5 IO window: disabled. MEM window: fe500000-fe5fffff PREFETCH window: disabled. PCI: Bus 4, cardbus bridge: 0000:03:01.0 IO window: 00001400-000014ff IO window: 00001800-000018ff PREFETCH window: 88000000-8bffffff MEM window: 8c000000-8fffffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: fe400000-fe4fffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:03:01.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 5807k freed VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:00:02.0 PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Allocate Port Service[0000:00:1c.5:pcie03] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20004100000, using 3072k, total 7616k vesafb: mode is 1024x768x16, linelength=2048, pages=3 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Linux agpgart interface v0.102 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: module loaded input: Macintosh mouse button emulation as /devices/virtual/input/input0 PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Freeing unused kernel memory: 252k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH8M: IDE controller (0x8086:0x2850 rev 0x02) at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16 ICH8M: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x6fa0-0x6fa7, BIOS settings: hda:DMA, hdb:pio ICH8M: IDE port disabled Probing IDE interface ide0... hda: HL-DT-ST DVD+/-RW GSA-T11N, ATAPI CD/DVD-ROM drive hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/33 mode selected ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 libata version 3.00 loaded. ata_piix 0000:00:1f.2: version 2.12 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: SATA max UDMA/133 cmd 0x6eb0 ctl 0x6eb8 bmdma 0x6ee0 irq 17 ata2: SATA max UDMA/133 cmd 0x6ec0 ctl 0x6ec8 bmdma 0x6ee8 irq 17 ata1.00: ATA-7: ST9120823AS, 3.ADB, max UDMA/133 ata1.00: 234441648 sectors, multi 8: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST9120823AS 3.AD PQ: 0 ANSI: 5 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 2-1: new full speed USB device using uhci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60 usb 2-1: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-1.1: new low speed USB device using uhci_hcd and address 3 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb 2-1.1: configuration #1 chosen from 1 choice usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 4 ports detected usb 2-1.1: can't set config #1, error -71 hub 2-1:1.0: hub_port_status failed (err = -71) hub 2-1:1.0: hub_port_status failed (err = -71) hub 2-1:1.0: hub_port_status failed (err = -71) ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000 usb 5-1: new full speed USB device using uhci_hcd and address 2 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 6 ports detected usb 2-1: USB disconnect, address 2 usb 2-1.1: USB disconnect, address 3 Driver 'sd' needs updating - please use bus_type methods sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > sd 0:0:0:0: [sda] Attached SCSI disk hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 usb 6-3: new high speed USB device using ehci_hcd and address 2 usb 6-3: configuration #1 chosen from 1 choice hub 6-3:1.0: USB hub found hub 6-3:1.0: 4 ports detected usb 6-3.1: new low speed USB device using ehci_hcd and address 3 usb 6-3.1: configuration #1 chosen from 1 choice usb 6-3.4: new high speed USB device using ehci_hcd and address 4 Attempting manual resume usb 6-3.4: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with journal data mode. usb 5-1: new full speed USB device using uhci_hcd and address 3 usb 5-1: configuration #1 chosen from 1 choice hub 5-1:1.0: USB hub found hub 5-1:1.0: 4 ports detected usb 5-2: new full speed USB device using uhci_hcd and address 4 usb 5-2: configuration #1 chosen from 1 choice input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.7/usb6/6-3/6-3.1/6-3.1:1.0/input/input2 input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1a.7-3.1 input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.7/usb6/6-3/6-3.1/6-3.1:1.1/input/input3 input,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.7-3.1 usb 5-1.2: new full speed USB device using uhci_hcd and address 5 usb 5-1.2: configuration #1 chosen from 1 choice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver tg3.c:v3.86 (November 9, 2007) ACPI: PCI Interrupt 0000:09:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:09:00.0 to 64 eth0: Tigon3 [partno(BCM95755m) rev a002 PHY(5755)] (PCI Express) 10/100/1000Base-T Ethernet 00:19:b9:89:0c:48 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] fuse init (API version 7.9) ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Battery Slot [BAT1] (battery absent) input: Lid Switch as /devices/virtual/input/input4 ACPI: Lid Switch [LID] input: Power Button (CM) as /devices/virtual/input/input5 ACPI: Power Button (CM) [PBTN] input: Sleep Button (CM) as /devices/virtual/input/input6 ACPI: Sleep Button (CM) [SBTN] ACPI: ACPI Dock Station Driver ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1b.0 to 64 iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux, 1.1.17ks iwl4965: Copyright(c) 2003-2007 Intel Corporation ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:0c:00.0 to 64 iwl4965: Detected Intel Wireless WiFi Link 4965AGN iwl4965: Radio disabled by HW RF Kill switch ACPI: SSDT 7F65C4F6, 0286 (r1 PmRef Cpu0Ist 3000 INTL 20050624) ACPI: SSDT 7F65BE8C, 05E5 (r1 PmRef Cpu0Cst 3001 INTL 20050624) Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state Monitor-Mwait will be used to enter C-3 state ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 7F65C77C, 00C4 (r1 PmRef Cpu1Ist 3000 INTL 20050624) ACPI: SSDT 7F65C471, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Thermal Zone [THM] (34 C) sd 0:0:0:0: Attached scsi generic sg0 type 0 input: PS/2 Mouse as /devices/virtual/input/input7 input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8 agpgart: Detected an Intel 965GM Chipset. agpgart: Detected 7676K stolen memory. agpgart: AGP aperture is 256M @ 0xe0000000 input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:2f/LNXVIDEO:00/input/input9 ACPI: Video Device [VID] (multi-head: yes rom: no post: no) input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:01/input/input10 ACPI: Video Device [VID1] (multi-head: yes rom: no post: no) ACPI Exception (video-1538): AE_OK, Invalid _DOD data [20070126] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:02/input/input11 ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) usbcore: registered new interface driver snd-usb-audio Linux video capture interface: v2.00 uvcvideo: Found UVC 1.00 device (046d:0990) usbcore: registered new interface driver uvcvideo USB Video Class driver (SVN r195) Yenta: CardBus bridge found at 0000:03:01.0 [1028:01fe] Yenta O2: res at 0x94/0xD4: 00/ea Yenta O2: enabling read prefetch/write burst rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k lp: driver loaded but no devices found PPP generic driver version 2.4.2 Yenta: ISA IRQ mask 0x0cb8, PCI irq 19 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07 pcmcia: parent PCI bridge Memory window: 0xfe400000 - 0xfe4fffff ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 ACPI: PCI Interrupt 0000:03:01.4[A] -> GSI 19 (level, low) -> IRQ 19 ppdev: user-space parallel port driver firewire_ohci: Added fw-ohci device 0000:03:01.4, OHCI version 1.10 firewire_core: created new fw device fw0 (0 config rom retries, S400) EXT3 FS on sda6, internal journal EXT2-fs warning (device sda3): ext2_fill_super: mounting ext3 filesystem as ext2 kjournald starting. Commit interval 5 seconds EXT3 FS on sda7, internal journal EXT3-fs: mounted filesystem with journal data mode. Adding 2048248k swap on /dev/sda5. Priority:-1 extents:1 across:2048248k NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present tg3: eth0: Link is down. tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present firewire_core: phy config: card 0, new root=ffc1, gap_count=5 firewire_core: created new fw device fw1 (0 config rom retries, S400) scsi2 : SBP-2 IEEE-1394 firewire_sbp2: logged in to fw1.1 LUN 0000 (0 retries) scsi 2:0:0:0: Direct-Access Maxtor OneTouch II 023g PQ: 0 ANSI: 4 sd 2:0:0:0: [sdb] 586114704 512-byte hardware sectors (300091 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 2f 00 00 00 sd 2:0:0:0: [sdb] Cache data unavailable sd 2:0:0:0: [sdb] Assuming drive cache: write through sd 2:0:0:0: [sdb] 586114704 512-byte hardware sectors (300091 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 2f 00 00 00 sd 2:0:0:0: [sdb] Cache data unavailable sd 2:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sdb2 sd 2:0:0:0: [sdb] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg1 type 0